Advantech AIMB-556 Uživatelský manuál

User ManualACP-2010MB2U-High Rackmount Chassis for ATX / MicroATX Motherboard

ACP-2010MB User Manual 21.1 IntroductionThe ACP-2010MB is a 2U-high rackmount industrial computer chassis. It meets a variety of application needs for

3 ACP-2010MB User ManualChapter 1 General Information1.3 Power Supply Options 1.4 Environmental SpecificationsTable 1.1: Power supply optionsModel N

ACP-2010MB User Manual 41.5 Dimension DiagramFigure 1.1 Dimension DiagramUnit: mm [inch]

Chapter 22 System SetupThis chapter introduces the instal-lation process.Sections include:! Installing a motherboard ! Installing a riser card or add-

ACP-2010MB User Manual 6The following procedures instruct users to install a motherboard, add-on cards, anddisk drives into the ACP-2010MB. Refer to A

7 ACP-2010MB User ManualChapter 2 System Setup2.2 Installing the MotherboardThe ACP-2010MB can support an ATX / MicroATX motherboard with up to three

ACP-2010MB User Manual 8Figure 2.3 Fasten the plastic postFigure 2.4 Installing a motherboard

9 ACP-2010MB User ManualChapter 2 System Setup2.3 Installing a Riser Card and Add-on Cards The ACP-2010MB supports up to three add-on

ACP-2010MB User Manual 10Figure 2.6 Installing an add-on cardIf you have the ACP-2010MB with the low-profile rear I/O bracket, then simply installthe

11 ACP-2010MB User ManualChapter 2 System Setup2.4 Installing Disk DrivesThe ACP-2010MB supports one 5.25" optical disk drive and three 3.5"

ACP-2010MB User Manual iiCopyrightThe documentation and the software included with this product are copyrighted 2008by Advantech Co., Ltd. All rights

ACP-2010MB User Manual 124. To install the optical disk drive and 3.5" FDD, undo the screws on the 5.25" disk drive bracket.5. Undo the scre

13 ACP-2010MB User ManualChapter 2 System Setup2.5 Attaching the Ears and HandlesThere are a pair of ears and handles in the accessory box, which may

ACP-2010MB User Manual 14

Chapter 33 OperationThis chapter introduces the sys-tem operation information.Sections include:! The front panel! The rear panel! Replacing the coolin

ACP-2010MB User Manual 163.1 The Front PanelThe front panel features a lockable door and four LED indicators. It provides frontaccessible, dual USB po

17 ACP-2010MB User ManualChapter 3 Operation3.1.2 LED Indicators for System StatusFour LEDs are placed on the left side of the front panel to indicate

ACP-2010MB User Manual 183.2 The Rear PanelThe rear panel comes with 3-slot I/O brackets, two reserved 9-pin D-SUB openingsand a motherboard I/O openi

19 ACP-2010MB User ManualChapter 3 Operation3.3 Replacing the Cooling FansThere are two easily maintained system cooling fans in the chassis. The fans

ACP-2010MB User Manual 203.4 Cleaning the FiltersThe filter functions to block dust or particles from the work environment and greatlyhelps to extend

21 ACP-2010MB User ManualChapter 3 Operation3.5 Replacing the Power SupplyThe ACP-2010MB supports either a 300 W or a 400 W 2-U-high power supply.To r

iii ACP-2010MB User Manual Safety Instructions 1. Read these safety in

ACP-2010MB User Manual 22

Chapter 44 Alarm BoardThis chapter introduces the alarm board and thermal sensor specifi-cations.Sections include:! Alarm board layout! Alarm board sp

ACP-2010MB User Manual 24The alarm board is located under the 3.5" disk drive bay. The alarm board providessystem detection functions that monito

25 ACP-2010MB User ManualChapter 4 Alarm Board4.2 Alarm Board Specifications! Input Power: +5 V, +12 V! Input Signals: – 7 "fan" connectors–

ACP-2010MB User Manual 26Table 4.6: CN18, Output connector to LED boardPin 1 GND Pin 9 Temperature GoodPin 2 +5 V signal Pin 10 Temperature Fail Pin 3

27 ACP-2010MB User ManualChapter 4 Alarm Board4.2.2 Switch SettingsThe alarm board is designed to connect with up to 7 fans. Users can set the fan num

ACP-2010MB User Manual 284.3 Thermal SensorThe ACP-2010MB is configured with a thermal sensor on the backside of the chassis(see Figure 4.2).Figure 4.

29 ACP-2010MB User ManualChapter 4 Alarm BoardTable 4.12: CN1 & CN2, Temperature sensor connectorPin 1 +5 V Pin 3 T_SDATPin 2 T_SCLK Pin 4 GNDTabl

ACP-2010MB User Manual 30

Appendix AA Exploded Diagram and Parts List

ACP-2010MB User Manual iv18. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) thi

ACP-2010MB User Manual 32Figure A.1 Exploded DiagramTable A.1: Parts List1 Key Set 13 Rack Mounting 25 Thermal Board2 Front Panel 14 Chassis 26 Rea

Appendix BB Motherboard & Riser Card Options

ACP-2010MB User Manual 34B.1 Motherboard Options The ACP-2010MB supports a variety of Advantech ATX / MicroATX motherboardsdes

35 ACP-2010MB User ManualAppendix B Motherboard & Riser Card OptionsB.2 Riser Card OptionsThe riser card is specially designed to support Advantec

www.advantech.comPlease verify specifications before quoting. This guide is intended for referencepurposes only.All product specifications are subject

v ACP-2010MB User Manual Product Warranty (2 years)Advantech warrants to you, the original purchaser, that each of its products will befree from defec

ACP-2010MB User Manual viInitial InspectionWhen you open the carton, please make sure that the following materials have beenshipped:! ACP-2010MB Chass

vii ACP-2010MB User Manual ContentsChapter 1 General Information ...11.1 Introduction ...

ACP-2010MB User Manual viiiTable 4.1: CN1, Auxiliary external power connector, standard mini 4-Pin power connector... 25Table 4.2:

Chapter 11 General InformationThis chapter provides general information about the ACP-2010MB.Sections include:! Introduction! Specifications! Power su