Advantech PCM-5864L Uživatelský manuál Strana 47
- Strana / 141
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Chapter 2 Installation 35
2.19.2 Network boot
The Network Boot feature can be utilized by incorporating the
Boot ROM image files for the appropriate network operating
system. The Boot ROM BIOS files are included in the system
BIOS, which is on the utility CD disc.
2.20 Watchdog timer configuration
An on-board watchdog timer reduces the chance of disruptions
which EMP (electro-magnetic pulse) interference can cause. This
is an invaluable protective device for standalone or unmanned
applications. Setup involves one jumper and running the control
software (refer to Appendix A).
2.20.1 Watchdog timer action (JP2)
When the watchdog timer activates (CPU processing has come to
a halt), it can reset the system or generate an interrupt on IRQ11.
This can be set via setting JP2 as shown below:
Table 2-21: Watchdog timer action (JP2)
*System reset IRQ11
JP2
* default setting
1
2
3
1
2
3
- PCM-5864/E/L 1
- Copyright Notice 2
- Packing list 3
- Contents 4
- General Information 13
- 1.1 Introduction 14
- 1.2 Features 15
- 1.3 Specifications 16
- Installation 21
- 2.1 Jumpers 22
- 2.2 Connectors 23
- 2.3 Locating jumpers 24
- 2.4 Locating connectors 25
- 2.4.2 Solder side 26
- 2.5 Setting jumpers 27
- Chapter 2 Installation 17 29
- 1.5 /3.5 2* 2.5 3 4 30
- 4.5 5 5.5 (reserved) 30
- *33 MHz CPU CLK/2 30
- 1 2 3 1 2 3 30
- * default setting 31
- 2.6.4 CMOS clear (J7) 32
- 2.7.1 Installing DIMMs 33
- 2.8.2 CompactFlash (CN501) 34
- Chapter 2 Installation 23 35
- 2.12.1 Speaker 37
- 2.12.2 LED interface 37
- 2.12.3 Watchdog output 37
- 2.12.4 Reset switch 37
- Chapter 2 Installation 27 39
- 2.15 IR connector (CN17) 40
- CN502) (PCM-5864/E only) 40
- J21) 41
- *RS-232 RS-422 RS-485 42
- Port Address range Interrupt 42
- *5 V 3.3 V 45
- SHFCLK* ASHFCLK 45
- 2.19 Ethernet configuration 46
- 2.19.2 Network boot 47
- 2.21 USB connectors (CN16) 48
- (PCM-5864 only) 49
- Software 51
- Configuration 51
- 3.1 Introduction 52
- (640 x 480 AD4 EL) 53
- LTM10C042 PCM-5864/E/L CN15 54
- Pin Name Pin Name 54
- LM64C142 PCM-5864/E/L CN15 55
- LTM12C275A PCM-5864/E/L CN15 56
- Award BIOS Setup 59
- 4.2 AWARD BIOS setup 61
- 4.2.2 Standard CMOS setup 62
- 4.2.3 BIOS features setup 63
- 4.2.4 Chipset features setup 64
- 4.2.5 Power management setup 65
- 4.2.6 PnP/PCI configuration 66
- 4.2.7 Integrated peripherals 67
- 4.2.8 Load BIOS defaults 68
- 4.2.9 Change password 69
- 4.2.10 Auto detect hard disk 70
- 4.2.11 Save & exit setup 70
- 4.2.12 Exit without saving 70
- PCI SVGA Setup 71
- 5.1 Before you begin 72
- 5.2 Introduction 72
- 5.2.2 Display memory 73
- 5.2.3 Display types 73
- D:\VGA\Win95\ 74
- Chapter 5 PCI SVGA Setup 63 75
- Chapter 5 PCI SVGA Setup 65 77
- ChipsCPL 78
- Chapter 5 PCI SVGA Setup 67 79
- D:\VGA\NT40\ 80
- Chapter 5 PCI SVGA Setup 69 81
- 5.4 Further information 82
- • Introduction 83
- Windows 95/98 83
- 6.1 Introduction 84
- Chapter 6 Video 73 85
- Chapter 6 Video 75 87
- Windows 95/98/NT 89
- 7.1 Introduction 90
- Chapter 7 Audio 79 91
- PCI Bus Ethernet 93
- Interface 93
- 8.1 Introduction 94
- 8.3 Further information 99
- Programming the 101
- Watchdog Timer 101
- Installing PC/104 105
- B.1 Installing PC/104 modules 106
- Pin Assignments 109
- CPU fan power connector (CN1) 110
- Pin Signal 111
- Speaker out connector (CN502) 112
- Audio connector (CN4) 112
- Aux line-in connector (CN7) 113
- Main power connector (CN8) 114
- * low active 116
- PC/104 connectors (CN11) 117
- IDE HDD connector (CN12) 118
- Front panel connector (CN15) 121
- USB connector (CN16) 121
- IR connector (CN17) 122
- CRT display connector (CN18) 122
- Video-out connector (CN19) 123
- Flat panel connector (CN20) 124
- Pin Signal Pin Signal 125
- COM port connector (CN23) 126
- Pin Signal Signal Signal 127
- LVDS connector (JP3) 130
- Assignments 131
- D.1 System I/O ports 132
- D.2 1st MB memory map 133
- D.3 DMA channel assignments 133
- D.4 Interrupt assignments 134
- Optional Extras 135
- E.1 PCM-10586-3 cable kit for 136
- PCM-5864/E/L 136
- E.3 Optional USB cable (CN16) 137
- Mechanical 138
- Drawings 138
- F.1 Component side 139
- F.2 Solder side 140
Související produkty a manuály pro Barebones pro PC / pracovní stanice Advantech PCM-5864L
(62 stránky)
(28 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce