Advantech MMP3-21 Uživatelský manuál Strana 83
- Strana / 112
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Advantech SOM-Express Design Guide
Chapter 5 Carrier Board Design Guidelines 83
SOM-Express
TX
RX
RX
TX
PCI
Express
Device
L2L3
L1
Figure 5-49 Topology #1 – SOM Express to PCI Express Device Down
Table 5-28 SOM Express to PCI Express
L1 L2 L3 Capacitor Value
Max = 14.75 inches
Min = 0.25 inches
Max = 14.5 inches
Max = 14.75
inches – L2
75 nF to 200 nF,
Tolerance = 20%,
Package: recommended to use 0603,
or use 0402 if necessary
5.10.3.4 PCI Express Topology #2 and #3 – Device Down Routing
Both the ExpressCard and the docking topologies allow a maximum of 10 inches
from SOM-Express pin to the pin of the down device. This maximum length takes into
account all routing, including the breakout region, which should not exceed 0.25
inches per device. The TX and RX pairs must be routed interleaved, such that the
pairs alternate between TX and RX on the carrier board to reduce crosstalk for
microstrip and stripline topologies.
SOM-Express
TX
RX
RX
TX
Express
Card or
Docking
connector
L1
L2
Figure 5-50 Topology #2 and #3 – SOM Express to Express Card or Docking Conn.
Table 5-29 SOM Express to Express Card
L1 L2 Capacitor Value
Max = 10 inches
Max = 10 inches 75 nF to 200 nF,
Tolerance = 20%,
Package: recommend to use 0603,
or use 0402 if necessary
- Advantech 1
- Notices 2
- Revision History 2
- Table of Contents 3
- 4 Table of Contents 4
- Table of Contents 5 5
- 6 Table of Contents 6
- Table of Contents 7 7
- 8 Table of Contents 8
- Chapter 1 Introduction 9
- 1.2 Referenced Documents 10
- 2.1 Overview 11
- 2.2 Specifications 13
- 2.2.1 SOM-5780 14
- 2.2.2 SOM-5782 16
- 2.2.3 SOM-DB5700 18
- 2.3 System Resources 19
- 2.3.1 SOM-5780 Resources 19
- 2.3.2 SOM-5782 Resources 22
- 2.4 PCI Routing 25
- 2.5 DC Specifications 25
- 2.5.1 Interface I/O Voltage 25
- 2.5.1.3 Audio 27
- 2.5.1.4 VGA 27
- 2.5.1.5 LCD 28
- 2.5.1.6 IDE 28
- 2.5.1.7 Ethernet 28
- 2.5.1.8 TV-Out Bus 28
- 2.5.1.9 IrDA 28
- 2.6 AC Specification 29
- 2.6.1 PCI-Bus AC Spec 29
- 2.6.3 Audio AC Spec 29
- 2.6.4 VGA AC Spec 29
- 2.6.5 IDE AC Spec 30
- 2.6.6 I2C AC Spec 30
- 2.6.7 SMBus AC Spec 30
- Chapter 3 Pin Assignments 31
- 3.1 Row A 32
- 3.2 Row B 33
- 3.3 Row C 34
- 3.4 Row D 35
- 4.1 Nominal Board Stack-Up 36
- Thickness 37
- 4.3 Alternate Stack Ups 39
- 5.1 PCI-Bus 40
- 5.1.1 Signal Description 40
- 5.1.2 Design Guidelines 41
- Vtest 0.4 Vcc 1.5 V 42
- Tskew 2 (max) 2 (max) ns 42
- 5.1.3 Layout Guidelines 44
- Carrier 45
- 5.1.4 Application Notes 46
- 5.2.1 Signal Description 47
- 5.2.2 Design Guidelines 47
- 5.2.3 Layout Guideline 48
- SOM-Express 49
- USB Connector 49
- 5.2.3.4 Stubs 50
- 5.3.1 Signal Description 51
- 5.3.2 Design Guidelines 51
- 5.3.2.3 Azalia: 52
- Analog Ground 53
- 5.3.3 Layout Guidelines 54
- ± 15% 54
- 5.4 VGA 56
- 5.4.1 Signal Description 56
- 5.4.2 Design Guidelines 57
- 5.4.3 Layout Guideline 57
- VGA Connector 58
- 5.5 LVDS 59
- 5.5.1 Signal Description 59
- 5.5.2 Design Guideline 59
- 5.5.3 Layout Requirements 60
- 5.6 Primary IDE0 61
- 5.6.1 Signal Description 61
- 5.6.2 Design Guidelines 61
- IDE bus IDE cable 62
- Total Max 62
- Length 13 inches 62
- Carrier Board 62
- 5.6.3 Layout Guidelines 63
- 5.7 Ethernet 64
- 5.7.1 Signal Descriptions 64
- 5.7.2 Design Guidelines 64
- LAN Connector 65
- 5.7.3 Layout Guidelines 66
- 5.7.3.2 Transformer 67
- 5.7.3.3 Critical Dimensions 68
- 5.8 TV-Out 70
- 5.8.1 Signal Descriptions 70
- 5.8.2 Design Guidelines 70
- TV DAC Filter 71
- 5.9 Miscellaneous 72
- Carrier board 74
- 5.10 PCI Express Bus 77
- 5.10.1 Signal Description 77
- Pin Signal I/O Description 77
- 5.10.3.1 Differential pairs 81
- Guidelines 82
- L1 L2 L3 Capacitor Value 83
- L1 L2 Capacitor Value 83
- 5.11 Serial ATA 84
- 5.11.1 Signal Description 84
- 5.11.2 Design Guidelines 84
- 5.11.3 Layout Guidelines 85
- 5.12 LPC 87
- 5.12.1 Signal Description 87
- 5.12.2 Design Guidelines 87
- 5.12.3 Layout Guidelines 87
- 5.12.4 Application Notes 88
- 5.12.4.3 LPT/Floppy 89
- 5.12.4.4 EMI Considerations 89
- Parallel Port 90
- 6.2 Design Guidelines 95
- 8.1 Material of Heatsink 101
- 8.4 Grounding Issues 102
- 8.8.1 Vendor List 106
- 8.8.2 Heat-Spreader 106
- 8.8.3 Heat-Sink 107
- 8.8.4 Thermal Pad 108
- M2.5*6 5 109
- M2.5*16 5 109
- Quantity 109
- 8.8.6 Fan 110
Související produkty a manuály pro Barebones pro PC / pracovní stanice Advantech MMP3-21
(30 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce