Advantech RS-100-RT Uživatelský manuál Strana 166
- Strana / 398
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
4-82 ADAM 4000 Series User's Manual
Command Set
4014D
$AA6(data_A)(data_B)
Name Write Source High/Low Values for Linear Mapping
Description Write the high/low limit values to a specified module for linear
mapping. The module will only activate the source values after
new target high/low values are written (Command $AA7).
Syntax $AA6(data_A)(data_B)(cr)
$ is a delimiter character.
AA (range 00-FF) represents the 2-character hexadecimal
address of the analog input module.
6 identifies the set high/low limit value for linear mapping
command.
(data_A) is the low limit input value of the module for linear
mapping. This value must be lower than the module’s high
limit input value for linear mapping (data_B). The data format
is the same as the module’s input current range. The minimum
value allowed is equal to the minimum input value of the
current range.
(data_B) is the high limit input value of the module for linear
mapping. This value must be greater than the module’s low
limit input value for linear mapping (data_A). The data format
is the same as the module’s input current range, and the
maximum value allowed is equal to the maximum input value
of the current range.
(cr) is the terminating character, carriage return (0Dh)
Response !AA(cr) if the command is valid.
The addressed module stores the high/low input values in a
buffer. The module updates these values only after the com-
mand $AA7(data_C) (data_D) is executed.
?AA(cr) if an invalid operation was entered.
There is no response if the module detects a syntax error or
communication error or if the specified address does not exist.
? is a delimiter character indicating the command was invalid.
AA (range 00-FF) represents the 2-character hexadecimal
address of an analog input module.
(cr) is the terminating character, carriage return (0Dh).
- ADAM 4000 1
- ADAM 4000 Series 3
- Table of Contents 4
- Introduction 7
- 1.1 Overview 8
- Installation Guideline 11
- Power Supply Connections 14
- +10~+30 V 16
- 2.3 Baud rate and Checksum 19
- Grounding the INIT* Terminal 20
- 2.4 Multiple Module Hookup 21
- 2.5 Application Example 22
- Chapter 2 23
- Figure 2-5 23
- I/O Modules 27
- ADAM-4012 Analog Input Module 33
- ADAM-4013 RTD Input Module 34
- Millivolt and Volt Input 35
- Thermocouple Input 35
- Process Current Input 36
- RTD Inputs 37
- Chapter 3 39
- Application Wiring 39
- Strain Gauge Voltage Input 44
- Strain Gauge Current Input 44
- Digital Output used with SSR 45
- Input Modules 46
- ADAM-4017 48
- Figure 3-17 49
- Eight differential 50
- JP9, Jp10 50
- ADAM-4018 51
- ADAM-4018M 52
- Figure 3-20 53
- Figure 3-21 55
- Figure 3-22 55
- Apllication Wiring 55
- T/C or 4~20mA 57
- INPUT RANGE 58
- –0~20 mA 59
- Analog Output 63
- ADAM-4050 Digital I/O Module 65
- DI15 INIT* 68
- INIT*DI15 68
- TTL Input (ADAM-4050) 71
- Figure 3-37 72
- Figure 3-38 72
- Figure 3-39 73
- Figure 3-40 73
- Wet Contact Input (ADAM-4053) 74
- ADAM-4060 Relay Output Module 76
- TYPE SIGNAL 77
- ADAM-4080 82
- ADAM-4080D 83
- Non-isolated Input 84
- Photo-isolated Input 84
- 4.1 Introduction 86
- 4.2 Syntax 86
- ADAM-4011 Command Table 88
- ADAM-4011D Command Table 90
- ADAM-4012 Command Table 92
- ADAM-4013 Command Table 94
- ADAM-4015 Command Table 95
- ADAM-4016 Command Table 96
- ADAM-4017 Command Table 99
- Command Set 100
- ADAM-4017+ Command Set 100
- Chapter 4 101
- ADAM-4018 Command Table 103
- ADAM-4018+ Command Set 104
- ADAM-4018M Command Table 107
- (continued on following page) 107
- ADAM-4019 Command Table 108
- ADAM-4021 Command Table 109
- ADAM-4050 Command Table 110
- ADAM-4052 Command Table 112
- ADAM-4053 Command Table 113
- ADAM-4055 Command Set Table 114
- ADAM-4060/4068 Command Table 115
- ADAM-4080 Command Table 116
- ADAM-4080D Command Table 120
- 76543210 128
- 4015, 4017, 4017+, 4018 138
- 4018+, 4018M, 4019 138
- 4016, 4019 143
- 4011D, 4015 146
- (number of counts) 148
- 4015, 4019 149
- IEC RTD 100O, α = 0.00385 152
- JIS RTD 100O, α = 0.00391 152
- Channel 7 174
- Channel 0 174
- Bit 3 Bit 2 Bit 1 Bit 0 181
- Decimal point 181
- 4011, 4011D, 4012, 4014D 200
- CMD To ADAM4024 231
- Suggest Timing : 231
- T0 : See Table 231
- T1 : 100ms 231
- ADAM-4024 4CH AO Module 232
- %AANNTTCCFF 236
- 01111010 240
- 00001010 240
- 7 6 5 4 3 2 1 0 252
- 4080, 4080D 254
- $AA0L(data) 278
- (ADAM-4080D) 295
- (ADAM-4080) 295
- Calibration 303
- Applying Calibration Voltage 304
- Span Calibration 305
- Zero Calibration 305
- Cold Junction Calibration 306
- Figure 5-5 309
- 5.3 Analog Output Calibration 311
- Technical Specifications 315
- Appendix A 317
- ADAM-4011 Function Diagram 318
- Technical specifications 320
- ADAM-4011D Function Diagram 321
- ADAM-4012 Function Diagram 323
- ADAM-4013 Function Diagram 325
- ADAM-4014D Function Diagram 327
- ADAM-4016 Function Diagram 329
- ADAM-4017 Function Diagram 331
- ADAM-4018 Function Diagram 332
- ADAM-4018M Function Diagram 337
- ADAM-4021 Function Diiagram 339
- ADAM-4050 Function Diagram 341
- ADAM-4052 Function Diagram 343
- ADAM-4053 Function Diagram 345
- ADAM-4060 Function Diagram 347
- ADAM-4080 Function Diagram 349
- LED Display 350
- ADAM-4080D Function Diagram 351
- Data Formats and 353
- I/O Ranges 353
- Data Formats and I/O Ranges 360
- Appendix B 361
- B.3 Analog Output Formats 365
- Technical Diagrams 369
- C.1 ADAM Dimensions 370
- C.2 Installation 371
- DIN-Rail Mounting 372
- C.2.2 Panel Mounting 373
- Appendix C 373
- Figure C-4 373
- Panel Mounting 374
- Piggyback Stack 375
- Utility Software 377
- Main screen 378
- Setup options 379
- Zero Calibration 381
- Terminal Emulation 382
- Operation setting 384
- Alarm setting 384
- RS-485 Network 387
- E.1 Basic Network Layout 388
- Daisychaining 389
- Star structure 389
- Random structure 390
- E. 2 Line Termination 391
- E.3 RS-485 Data Flow Control 394
- How to use the 395
- Checksum feature 395
- F.1 Checksum Enable/Disable 396
Související produkty a manuály pro Servery Advantech RS-100-RT
Servery Advantech RS-400-SF Uživatelský manuál
(91 stránky)
(91 stránky)
Servery Advantech EKI-1122L Uživatelský manuál
(60 stránky)
(60 stránky)
Servery Advantech EKI-1122L Uživatelský manuál
(16 stránky)
(16 stránky)
Servery Advantech RS-200-RT Uživatelský manuál
(88 stránky)
(88 stránky)
Servery Advantech RS-100-RT Uživatelský manuál
(79 stránky)
(79 stránky)
Servery Advantech EKI-1122L Uživatelský manuál
(47 stránky)
(47 stránky)
Servery Advantech EKI-1351 Uživatelský manuál
(76 stránky)
(76 stránky)
Servery Advantech EKI-1122L Uživatelský manuál
(2 stránky)
(2 stránky)
Servery Advantech PCL-848A/B Specifikace
(56 stránky)
(56 stránky)
ETC Unison Heritage Contact and Fader Interface Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Schalttafel ETC Unison Heritage Contact and Fader Interface.
Wir stellen 1 PDF-Handbücher ETC Unison Heritage Contact and Fader Interface zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentáře k této Příručce