Advantech 5000 Series Uživatelský manuál Strana 241
- Strana / 301
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Quick Start Example
0F = set input range to type K thermocouple
00 = set data format to engineering units, 50ms (60Hz)
(See Chapter 6, Command Set for a full description of the syntax of the
configuration command for an analog input module)
When the module received the configuration command it will respond
with its new address:
!01(cr)
Wait 7 seconds to let the new configuration settings take effect before
issuing a new command to the module.
Note:
All reconfiguration except changing of baud rate and
checksum values can be done dynamically, i.e. the
modules need not be reset.
When changing baud
rate or checksum, these changes should be made for
all connected devices. After reconfiguration, all
modules should be powered down and then powered
up to force a reboot and let the changes take effect.
See the next section for a strategy for changing baud
rate and or checksum for an entire network.
A.3 Baud Rate and Checksum
ADAM-5000 systems contain an EEPROM to store configuration
information and calibration constants. The ROM replaces the usual
array of switches and pots required to specify baud rate, input/output
range, etc. The ADAM-5000 system can be configured remotely
through their communication ports, without having to physically alter
pot or switch settings.
Since there is no visual indication of a system's configuration status, it
is not possible to visually determine baud rate and other system
settings. It might not be possible to establish communications with a
system whose baud rate and address are unknown. To overcome this
problem, every system has an input terminal labeled INIT*. By
booting the system while connecting the INIT* terminal with the
system's GND terminal, the system configuration is forced into a
A-8 ADAM-5000
- ADAM-5000 Series 1
- Edition 7.3 2
- Aug. 2007 2
- A Message to the Customer… 3
- Advantech Customer Services 3
- Product Warranty 4
- Contents 6
- Figures 10
- Introduction 13
- Chapter 1 14
- 1.2 System Configuration 14
- Installation Guideline 17
- Chapter 2 20
- 2.2 Module Installation 21
- RS-232 Port Connection 27
- Connection(ADAM-5000E only) 28
- ADAM-5000 System 30
- 3.1 Overview 31
- The CPU’s Basic Functions 31
- Chapter 3 32
- Connectivity and Programming 33
- 3.3 System Setup 35
- I/O modules 38
- ADAM-5000 39
- Software Utilities 40
- 5.1.2 Save Function 42
- 5.1.3 COM Port Settings 43
- Chapter 5 44
- Baud rate: 44
- Prefix Char: 44
- Timeout: 44
- 5.1.5 Terminal Emulation 46
- 5.1.6 Data Scope 47
- 5.1.9 Module Configuration 53
- Chapter 5 54
- 5.1.10 Module Calibration 54
- Zero Calibration: 54
- 5-16 ADAM-5000 54
- 5-16 ADAM-5000 55
- 5.1.12 Alarm Setting 60
- Digital Filter 60
- 5.1.13 Download Procedure 61
- 6-4 ADAM-5000 69
- %aannccff 71
- 6-16 ADAM-5000 81
- 5013 RTD Input 85
- 5013 RTD Input 97
- Chapter 6 100
- Command Set 101
- 5013 RTD Input 101
- 5017/5018 103
- Analog Input 103
- Analog Input 107
- Analog Input Command Set 122
- $aaSiCjrrFF 125
- $aaSiCjB 127
- $aaSiAFFff 129
- 6-66 ADAM-5000 131
- #aaSiCj 135
- Command Set 137
- 5013/5017/5017H/5017UH/5018 153
- Analog Input Alarm 153
- 5024 Analog Output 155
- 5024 Analog Output 159
- $aaSiBB(data) 175
- 6-116 ADAM-5000 181
- 5080 Counter/ 183
- Chapter 6 184
- Troubleshooting 228
- 7.1 Hardware Diagnosis 229
- 7.2 Software Diagnosis 229
- Chapter 7 230
- Quick Start Example 234
- Appendix A 236
- Data Formats and I/O Ranges 247
- Appendix B 248
- B-6 ADAM-5000 251
- RS-485 Network 258
- Appendix C 260
- Daisychain 260
- Star Layout 261
- C.2 Line Termination 263
- Checksum Feature 268
- D.1 Checksum Enable/Disable 269
- Appendix D 270
- Printable ASCII Characters 271
- Appendix E 272
- E.2 Grounding Scheme 273
- Appendix E 274
- Appendix F 278
- Overview 279
- Appendix F 280
- Appendix F 282
- Grounding Reference 283
- 284
- 1.5 Single Point Grounding 285
- Appendix G 298
Související produkty a manuály pro Hardware Advantech 5000 Series
Hardware Advantech AIMB-258 Uživatelský manuál
(84 stránky)
(84 stránky)
Hardware Advantech UNO 2173A/AF Uživatelský manuál
(42 stránky)
(42 stránky)
Hardware Advantech 4718 Uživatelský manuál
(54 stránky)
(54 stránky)
Hardware Advantech EKI-2525P Uživatelský manuál
(28 stránky)
(28 stránky)
Hardware Advantech INTEL AIMB-210 Uživatelský manuál
(96 stránky)
(96 stránky)
ETC Unison Heritage Contact and Fader Interface Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Schalttafel ETC Unison Heritage Contact and Fader Interface.
Wir stellen 1 PDF-Handbücher ETC Unison Heritage Contact and Fader Interface zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentáře k této Příručce