Advantech PCA-6180 Specifikace Strana 134
- Strana / 176
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
116
PCA-6180 User’s Manual
9.7 Using SCSI Disk Utilities
To access the SCSI disk utilities, follow these steps:
1. Select the SCSI Disk Utilities option from the menu that
appears after starting SCSISelect. SCSISelect scans the SCSI bus
(to determine the devices installed) and displays a list of all SCSI
IDs and the devices assigned to each ID.
2. Use the arrow keys to move the cursor to a specific ID and
device, then press Enter.
3. A small menu appears, displaying the options Format Disk and
Verify Disk Media.
• Format Disk—Allows you to perform a low-level format on a
hard disk drive. Most SCSI disk devices are preformatted at the
factory and do not need to be formatted again.
Caution: A low-level format destroys all data on the drive. Be
sure to back up your data before performing this
operation. You
cannot
abort a low-level format once
it is started.
• Verify Disk Media—Allows you to scan the media of a hard
disk drive for defects. If the utility finds bad blocks on the
media, it prompts you to reassign them; if you select yes, those
blocks are no longer used. Pressing Esc at any time aborts the
utility.
- PCA-6180- B 1
- Copyright notice 3
- Acknowledgements 3
- A Message to the Customer 4
- Product warranty 7
- Initial Inspection 8
- Contents 9
- Hardware Configuration 19
- 1.1 Introduction 20
- 1.2 Features 21
- 4 PCA-6180 User's Manual 22
- 1.3 Specifications 23
- 1.3.4 VGA interface 24
- 1.3.5 SCSI interface 24
- 1.3.6 Ethernet LAN 24
- 1.3.7 Industrial features 24
- 8 PCA-6180 User's Manual 26
- 1.5 Jumpers and Connectors 27
- Table 1-2: Connectors 28
- 1.7 Safety Precautions 31
- 1.8 Jumper Settings 32
- Function Jumper setting 33
- IRQ11 1-2 closed 33
- * Reset 2-3 closed 33
- 1.9 System Memory 34
- 1.11 Cache Memory 36
- 1.12 CPU Installation 37
- Connecting Peripherals 39
- 2.1 Introduction 40
- Connectors 40
- 2.4 Parallel Port (CN4) 41
- 2.5 SCSI Connector (CN5) 42
- 2.6 USB Ports (CN31 and CN32) 43
- 2.7 VGA Connector (CN7) 43
- (CN8 and CN34) 44
- CN9 COM1 3F8*, 3E8 IRQ4 45
- CN10 COM2 2F8*, 2E8 IRQ3 45
- (CN11 and CN33) 46
- 2.13 CPU Fan Connector (CN14) 47
- CN18, CN19, CN21 and CN22) 48
- 2.14.4 HDD LED (CN19) 49
- 2.16 SM Bus Connector (CN23) 50
- Award BIOS Setup 51
- 3.1 Introduction 52
- 3.2 Entering Setup 52
- 3.3 Standard CMOS Setup 53
- 3.4 Advanced BIOS Features 54
- 3.4.12 Typematic Delay (msec) 56
- 3.4.13 Security Option 56
- 3.4.9 Gate A20 Option 56
- 3.4.10 Typematic Rate Setting 56
- 3.5 Advanced Chipset Features 57
- 3.5.1 SDRAM CAS Latency Time 58
- 3.5.3 SDRAM RAS-to-CAS Delay 58
- 3.6 Integrated Peripherals 60
- 3.6.10 UART Mode Select 62
- 3.6.11 RxD, TxD Active 62
- 3.6.12 IR Transmission Delay 62
- 3.6.13 UR2 Duplex Mode 62
- 3.6.14 Use IR Pins 63
- 3.6.17 EPP Mode Select 63
- 3.6.18 ECP Mode Use DMA 63
- 3.7 Power Management Setup 64
- 3.8 PnP/PCI Configurations 65
- 3.9 PC Health Status 66
- 3.9.3 Current CPU Temperature 67
- 3.9.4 Current CPUFAN Speed 67
- 3.9.5 +5V/+12V/-12V/-5V 67
- 3.9.6 Shutdown Temperature 67
- 3.10 Load Setup Defaults 68
- 3.11 Password Setting 68
- 3.12 Save & Exit Setup 69
- 3.13 Exit Without Saving 69
- Chipset Software Instal 71
- 4.1 Before You Begin 72
- 4.2 Introduction 72
- AGP SVGA Setup 77
- 5.1 Introduction 78
- 5.2 Installation 78
- Chapter 5 AGP SVGA Setup 61 79
- Chapter 5 AGP SVGA Setup 63 81
- LAN Configuration 83
- 6.1 Introduction 84
- 6.2 Features 84
- 6.3 Installation 85
- "Finish." 91
- PCA-6180 User's Manual 100
- Chapter 6 LAN Configuration 101
- "Next." 101
- Procedure 103
- Ultra ATA 100 Storage 105
- Driver Setup 105
- 7.1 Introduction 106
- 7.2 Features 106
- 7.3 Installation 107
- License Agreement 108
- Onboard Security Setup 113
- 8.1 Introduction 114
- 8.2 Installation 114
- SCSI Setup and 123
- Configurations 123
- 9.1 Introduction 124
- 9.2 Understanding SCSI 124
- 9.3 SCSI IDs 125
- 9.4 Terminating the SCSI Bus 126
- 9.5 Starting SCSI 128
- 9.6 Using SCSI 129
- Settings 129
- Boot Device Options 130
- SCSI Device Configuration 130
- PCA-6180 User’s Manual 132
- 9.7 Using SCSI Disk Utilities 134
- Programming the 135
- Watchdog Timer 135
- A.1.4 Example Program 139
- Pin Assignments 145
- PCA-6180 User's Manual 146
- Appendix B Pin Assignments 147
- B.4 SCSI Connector (CN5) 149
- B.5 USB Connector (CN6) 150
- B.6 VGA Connector (CN7) 150
- Connector (CN8, CN34) 151
- (CN9, CN10) 151
- B.11 IR Connector (CN13) 153
- B.15 Reset Connector (CN18) 155
- B.16 HDD LED Connector (CN19) 155
- B.19 H/W Monitor Alarm (CN22) 156
- B.20 SM Bus Connector (CN23) 156
- B.24 System I/O Ports 159
- B.25 DMA Channel Assignments 160
- B.26 Interrupt Assignments 160
- B.27 1st MB Memory Map 161
- B.28 PCI Bus Map 161
- Security Driver 163
- Installation Guide 163
- C.1 Security Driver 164
- C.2 Software Installation 165
- Appendix C DiskOnChip 167
- C.5 TROUBLESHOOTING 175
Související produkty a manuály pro Barebones pro PC / pracovní stanice Advantech PCA-6180
(22 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce