Advantech PCL-818 Series Uživatelský manuál stáhnout pdf (Strana 66)

PCL-818 Series User Manual 58

DMAE Disable/enable DMA transfers

0 Disables DMA transfers

1 Enables DMA transfer. Each A/D conversion initiates two

successive DMA request signals. These signals cause the

8237 DMA controller to transfer two bytes of conversion

data from the PCL-818HD/HG/L to memory.

ST1 to ST0 Trigger source

Note: Make sure that the IRQ level you choose is not

being used by another I/O device.

Note: You must program the PC's 8237 DMA controller

the DMA page register before you set DMAE to 1.

Trigger Source ST1 ST0

Software trigger 0 X

External trigger 1 0

Pacer trigger 1 1

1 2 ... 61 62 63 64 65 66 67 68 69 70 71 72 73 74

PCL-818 Series 1
User Manual 1
PCL-818 Series User Manual ii 2
PCL-818 Series User Manual iv 4
PCL-818 Series User Manual vi 6
Contents 7
Overview 9
Chapter 1 Overview 10
1.2 Features 11
1.3 Applications 12
1.4 Installation Guide 13
PCL-818 Series User Manual 6 14
1.5 Software Overview 15
1.6 Device Driver Roadmap 16
9 Chapter 1 17
1.7 Accessories 18
Installation 19
Chapter 2 Installation 20
2.2 Driver Installation 21
PCL-818 Series User Manual 14 22
2.3 Hardware Installation 23
PCL-818 Series User Manual 16 24
17 Chapter 2 25
Figure 2.5: Device Name 26
Figure 2.6: Test Utility 27
PCL-818 Series User Manual 20 28
Signal Connections 29
Chapter 3 Signal Connections 30
23 Chapter 3 31
PCL-818 Series User Manual 24 32
Switches Function Description 32
Jumpers Function Description 32
25 Chapter 3 33
JP11 External 33
Internal (default) 33
PCL-818 Series User Manual 28 36
Table 3-8: Jumper Settings 37
3.3 Signal Connections 38
31 Chapter 3 39
PCL-818 Series User Manual 32 40
33 Chapter 3 41
PCL-818 Series User Manual 34 42
35 Chapter 3 43
PCL-818 Series User Manual 36 44
Specifications 45
Appendix A Specifications 46
A.2 Analog Output 47
A.3 Digital Input /Output 47
A.4 Counter/Timer 48
A.5 General 48
Block Diagram 49
Appendix B Block Diagram 50
Register Structure & 51
C.1 Overview 52
C.2 I/O Port Address Map 52
Range codes appear below: 57
51 Appendix C 59
Bit # 7 6 5 4 3 2 1 0 59
C.9 D/A Output — BASE+04/05H 61
PCL-818 Series User Manual 54 62
Write FIFO interrupt control 62
Bit # 7 6543 2 1 0 62
BASE + 06H X X X X X X X FINT 62
C.12 A/D Status — BASE+08H 63
PCL-818 Series User Manual 56 64
C.13 A/D Control — BASE+09H 65
PCL-818 Series User Manual 58 66
Trigger Source ST1 ST0 66
Software trigger 0 X 66
External trigger 1 0 66
Pacer trigger 1 1 66
59 Appendix C 67
Write Timer/Counter enable 67
Bit # 7654321 0 67
BASE + 0AH TC1 TC0 67
C.18 FIFO Status — BASE+19H 69
C.19 FIFO Clear — BASE+19H 70
Calibration 71
Appendix D Calibration 72
D.1 VR Assignment 73
D.2 A/D Calibration 74
D.3 D/A Calibration 74

Komentáře k této Příručce

Žádné komentáře

Advantech PCL-818 Series Uživatelský manuál Strana 66

Komentáře k této Příručce

Související produkty a manuály pro Barebones pro PC / pracovní stanice Advantech PCL-818 Series