Advantech PCI-1710HG Specifikace Strana 160
- Strana / 164
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
150
corresponding D/A registers (BASE+10 and BASE+12).
7. Writing the value from 0x0600 to 0x06FF sequentially to
Calibration Command and Data register (BASE+18), and get
each bipolar range’s data by software trigger A/D method. Be
noted that to repeat this procedure 1000 times then to average
those data for each value. After that, to see whether the
discrepancy is less then 0.4 LSB. If so, to go to next step.
Otherwise, you must change the value and repeat all the procedure
in this step again until the discrepancy is less then 0.4 LSB.
8. Adjust UNIPOLAR offset calibration. First, writing any value to
BASE+9 to clear FIFO. Then to set the A/D range as -5 V to +5 V,
and to set the D/A range as 0 V to 5 V. Next, writing 0x8000 to
corresponding D/A registers (BASE+10 and BASE+12).
9. Writing the value from 0x0600 to 0x06FF sequentially to
Calibration Command and Data register (BASE+18), and get
each bipolar range’s data by software trigger A/D method. Be
noted that to repeat this procedure 1000 times then to average
those data for each value. After that, to see whether the average
data is close to 32767.5. If so, to go to next step. Otherwise, you
must change the value and repeat all the procedure in this step
again until the average data close to 32767.5.
10. Repeat steps 2 to 9 several times.
- Contents 3
- Figures 9
- Introduction 11
- 1. Introduction 13
- 1.1 Features 15
- Plug-and-Play Function 16
- Short Circuit Protection 18
- 1.2 Installation Guide 19
- 1.3 Software 21
- 1.4 Accessories 22
- Installation 25
- 2. Installation 27
- 2.2 Driver Installation 29
- 30
- 2.3 Hardware Installation 31
- Setting Up the Device 34
- Configuring the Device 36
- 2.5 Device Testing 38
- 1710HG/1711/1716) 40
- Testing Counter Function 43
- Signal Connections 45
- 3. Signal Connections 47
- 1710HGL/1711L/1716L 49
- is 1 kW, and each of the 55
- Software Overview 61
- 4. Software Overview 63
- Register-level Programming 64
- Programming Tools 64
- Calibration 69
- 5. Calibration 71
- VR Assignment 72
- VR assignment 73
- A/D Calibration 74
- Self A/D Calibration 75
- Calibration Utility 82
- A/D channel Auto-Calibration 84
- D/A channel Auto-Calibration 86
- Manual A/D Calibration panel 90
- Choosing Output Voltage 92
- Fig. 5-19) 93
- Appendixes 95
- Appendix A. Specifications 97
- Analog Output 98
- Analog Input 100
- Digital Input/Output 101
- Programmable Counter/Timer 101
- General 101
- Counter/Timer 103
- Appendix B. Block Diagrams 105
- C.1 Overview 109
- C.2 I/O Port Address Map 110
- PCI-1711/1711L 121
- Example 1 125
- Example 2 125
- Warning! 127
- Table C-9 Control Register 128
- Table C-10 Status Register 131
- BASE+11 132
- BASE+13 134
- PCI-1710/1710HG/1711/1716 136
- Function 143
- Counter 1 & 2 144
- Description: 146
- D.3 Counter Operating Modes 149
- D.4 Counter Operations 152
- Counter Latch Operation 153
- (Manually) 155
- F.1 Introduction 163
- F.2 Features 164
- F.3 Applications 164
Související produkty a manuály pro ne Advantech PCI-1710HG
ne Advantech PCI-1240 Uživatelský manuál
(34 stránky)
(34 stránky)
ne Advantech PCI-1731 Uživatelský manuál
(3 stránky)
(3 stránky)
ne Advantech PCA-6005-B Uživatelský manuál
(2 stránky)
(2 stránky)
ne Advantech PCI-1734 Uživatelský manuál
(3 stránky)
(3 stránky)
ne Advantech PCI-1730 Uživatelský manuál
(54 stránky)
(54 stránky)
ETC Unison Heritage Contact and Fader Interface Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Schalttafel ETC Unison Heritage Contact and Fader Interface.
Wir stellen 1 PDF-Handbücher ETC Unison Heritage Contact and Fader Interface zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentáře k této Příručce